CÁC LOẠI CÁNH KHUẤY
Contents
Hãng : Ametek Brookfield – USA
LV spindles
- Các loại cánh khuấy cho máy đo độ nhớt Brookfield dòng LV/ Rheometer Brookfield dòng LV được trang bị với bộ cánh khuấy tiêu chuẩn (LV-1 đến LV-4) với cấu trúc bằng thép không gỉ #302, có thể chọn thêm loại thép không gỉ #316 hoặc phủ Teflon để tăng khả năng chống ăn mòn.
- Giá đỡ cho các loại cánh khuấy tùy chọn để lưu trữ thuận tiện và cho phép lấy ra dễ dàng và nhanh chóng cho tất cả các cánh khuấy
Cánh khuấy LV-5 là chọn thêm được thiết kế riêng để tăng thang đo.
Cánh khuấy LV-2C và LV-3C là chọn thêm dạng “cylindrical spindles” để tính toán lực cắt shear rates.
Thông số kỹ thuật :
| Model | Range* |
| LV-1 (61) | 15-20K |
| LV-2 (62) | 50-100K |
| LV-3 (63) | 200-400K |
| LV-4 (64) | 1K-2M |
| LV-5 (65) | 2K-4M LV-5 is an optional spindle designed to increase measuring range |
| LV-2C | 50-100K |
| LV-3C | 200-400K |
*Based on standard LV speeds .3-60 rpm.
M=1million K=1 thousand
Note: LV-1 through LV-4 are supplied with LV instruments
LV-2C & LV-3C are optional “cylindrical spindles” offering geometry for calculating shear rates.
LV and RV/HA/HB spindles are supplied in 302 stainless steel.
Optional 316 stainless or Teflon coated spindles are available
Thông số kỹ thuật các loại cánh khuấy :
| RV/HA/HB Spindles cP(mPa•s) | |||
| SPINDLE | RANGE* RV SERIES | RANGE* HA SERIES | RANGE* HB SERIES |
| RV-1** | 100 – 20K | 200 – 40K | 800 – 160K |
| HA/HB-1** | 100 – 20K | 200 – 40K | 800 – 160K |
| RV-2 | 100 – 80K | 200 – 160K | 800 – 640K |
| HA/HB-2 | 100 – 80K | 200 – 160K | 800 – 640K |
| RV/HA/HB-3 | 100 – 200K | 200 – 400K | 800 – 1.6M |
| RV/HA/HB-4 | 200 – 400K | 400 – 800K | 1.6K – 3.2M |
| RV/HA/HB-5 | 400 – 800K | 800 – 1.6M | 3.2K – 6.4M |
| RV/HA/HB-6 | 1K – 2M | 2K – 4M | 8K – 16M |
| RV /HA/HB-7 | 4K – 8M | 8K – 16M | 32K – 64M |
* Based on standard RV/HA/HB speeds .5-100 RPM.
Note : LV and RV/HA/HB spindles are supplied in 302 stainless steel.
Optional 316 stainless or teflon coated spindles are available
** This spindle available as an option
Sample Rack
RV/HA/HB Spindle Set includes spindles #2 – #7 and is supplied with standard AMETEK Brookfield Viscometers and Rheometers.
Spindle #1 is available as an option.
Spindle Rack is also available as an option with both LV and RV/ HA/HB spindle sets.
| Wells/Brookfield Spindles & Cups | ||||
|
SPINDLE |
SHEAR
RATE |
SAMPLE VOLUME | CONE
ANGLE |
CONE
RADIUS |
| CPA-40Z | 7.50N sec-1 | .5mL | .8° | 2.4cm |
| CPA-41Z | 2.00N sec-1 | 2.0mL | 3° | 2.4cm |
| CPA-42Z | 3.84N sec-1 | 1.0mL | 1.5° | 2.4cm |
| CPA-51Z | 3.84N sec-1 | .5mL | 1.5° | 1.2cm |
| CPA-52Z | 2.00N sec-1 | .5mL | 3° | 1.2cm |
| CUP | ||||
| CPA-44YZ | Standard cup without temperature probe | |||
| CPA-44PYZ | Standard cup with RTD temperature probe | |||
| PCPA-3YZ | Cup with 1 purge fitting | |||
| PCPA-6YZ | Cup with luer fitting and 1 purge fitting | |||
| PCPA-4YZ | Cup with luer fitting and 2 purge fittings | |||
| PCPA-7YZ | Cup with luer fitting and 4 purge fittings | |||
Note : 1. Wells-Brookfield cones and cups are calibrated at the factory.
Cones ordered after shipment require cups to be returned for calibration to new cone.
- CPA cups and spindles are compatible with CPE cups and spindles.
| CAP Spindles | ||||
|
SPINDLE |
SHEAR
RATE |
SAMPLE VOLUME | CONE
ANGLE |
CONE
RADIUS |
| CAP-01 | 13.3N sec-1 | 67 µL | 0.45° | 1.511cm |
| CAP-02 | 13.3N sec-1 | 38 µL | 0.45° | 1.200cm |
| CAP-03 | 13.3N sec-1 | 24 µL | 0.45° | 0.953cm |
| CAP-04 | 3.3N sec-1 | 134 µL | 1.8° | 1.200cm |
| CAP-05 | 3.3N sec-1 | 67 µL | 1.8° | 0.953cm |
| CAP-06 | 3.3N sec-1 | 30 µL | 1.8° | 0.702cm |
| CAP-07 | 2.0N sec-1 | 1700 µL | 3.0° | 2.399cm |
| CAP-08 | 2.0N sec-1 | 400 µL | 3.0° | 1.511cm |
| CAP-09 | 2.0N sec-1 | 100 µL | 3.0° | 0.953cm |
| CAP-10 | 5.0N sec-1 | 170 µL | 1.2° | 1.511cm |
Note : 1. Recommend ordering calibration fluids specific to cone for field calibration
| UL Spindles & Chambers | |||
| SPINDLE | TYPE | SAMPLE VOLUME | SHEAR RATE |
| YULA-15(E) | Spindle – 304 stainless steel | 1.224N | |
| YULA-15(E)Z | Spindle – 316 stainless steel | 1.224N | |
| ULA-31(E)Y | Sample Chamber – 304 stainless steel | 16mL | |
| ULA-31(E)YZ | Sample Chamber – 316 stainless steel | 16mL | |
| SPINDLE | SAMPLE VOLUME | SHEAR RATE |
| ULA-DIN-85 | 1.29N | 17.0mL |
| ULA-DIN-86 | 1.29N | 6.5mL |
| ULA-DIN-87 | 1.29N | 2.0mL |
| HT-DIN-81 for Thermosel | 1.29N | 7.0mL |
| SC4-DIN-82 for SSA | 1.29N | 1.5mL |
| SC4-DIN-83 for SSA | 1.29N | 1.5mL |
| CHAMBER | ||
| ULA-DIN-6Y for use with ULA-DIN-86 and 87 | ||
| DAA-1 for use with ULA-DIN-85 | ||
| RST Spindles | ||||
| SPINDLE | VISCOSITY RANGE | SHEAR RATE | MAX. SHEAR STRESS | SAMPLE VOLUME |
| COAXIAL | Pa•s | sec-1 | Pa | Ml |
| CCT-DG | 0.00005-4.07K | 0.043-5.64K | 177 | 15.7 |
| CCT-40 | 0.0003-27.6K | 0.0215-2.79K | 594 | 68.5 |
| CCT-25 | 0.002-177K | 0.013-1.67K | 2.28K | 16.8 |
| CCT-14 | 0.012-1M | 0.013-1.68K | 13K | 3.4 |
| CCT-8 | 0.065-5.41M | 0.013-1.672K | 69.6K | 1.0 |
| CONE | ||||
| RCT-25-1 | 0.005-407K | 0.06-7.8K | 24.4K | 0.1 |
| RCT-25-2 | 0.01-814K | 0.03-3.9K | 24.4K | 0.2 |
| RCT-50-1 | 0.0006-50.9K | 0.06-7.8K | 3.05K | 1.0 |
| RCT-50-2 | 0.0012-101K | 0.03-3.9K | 3.05K | 2.0 |
| RCT-75-1* | 0.0002-15K | 0.06-7.8K | 905 | 2.5 |
| RCT-75-2* | 0.0004-30K | 0.03-3.9K | 905 | 5.0 |
| PLATE | ||||
| RPT-25 | 0.03-2.49M | 0.013-1.7K | 32.6K | 0.5 |
| RPT-50 | 0.002-155K | 0.027-3.4K | 4.07K | 2.0 |
| RPT-75* | 0.0004-30.7K | 0.04-5.1K | 1.2K | 4.5 |
*For use with water bath version only
Note: Values based on minimum speed of 1 RPM and maximum speed of 1000 RPM
1 Pa•s = 1,000 cP K = 1 thousand M = 1 million
| RST Vane Spindles | |||
| SPINDLE | VANE LENGTH | VANE DIAMETER | SHEAR STRESS |
| mm | mm | Pa | |
| VT-10-5 | 10 | 5 | 330-210K |
| VT-20-10 | 20 | 10 | 41-27K |
| VT-20-20 | 20 | 20 | 9-5.9K |
| VT-30-15 | 30 | 15 | 12-8K |
| VT-40-20 | 40 | 20 | 5.2-3.4K |
| VT-40-40 | 40 | 40 | 1.2-740 |
| VT-50-25 | 50 | 25 | 2.7-1.7K |
| VT-60-8 | 60 | 8 | 24-15K |
| VT-60-15 | 60 | 15 | 7-4.3K |
| VT-60-30 | 60 | 30 | 1.6-1K |
| VT-80-40 | 80 | 40 | 0.7-420 |
| VT-80-70 | 80 | 70 | 0.2-120 |
Values based on minimum speed of 1 RPM and maximum speed of 1000 RPM K = 1 thousand
| Thermosel Spindles and Chambers Link hanging configuration is standard | ||
| SPINDLE | SHEAR RATE | SAMPLE VOLUME |
| SC4-18 | 1.32N | 8.0mL |
| SC4-31 | .34N | 10.0mL |
| SC4-34 | .28N | 9.5mL |
| SC4-21 | .93N | 8.0mL |
| SC4-27** | .34N | 10.5mL |
| SC4-28 | .28N | 11.5mL |
| SC4-29 | .25N | 13.0mL |
| HT-DIN-81 | 1.29N | 7.0mL |
*SC4-XXBS = Solid Shaft. Not available for SC4-18 and SC4-21 spindles
**Also available as SC4-27D-100 = Disposable spindle, 100 units • SC4-DSY Chuck/Closer is required
| CHAMBER | TYPE |
| HT-2 | Sample Chamber – Reuseable, stainless steel |
| HT-2DB-100 | Sample Chamber – Disposable, aluminum, 100 units |
| Small Sample Spindles and Chambers | |||
| SPINDLE | SAMPLE CHAMBER | SHEAR RATE | SAMPLE VOLUME |
| SC4-18 | 13R | 1.32N | 6.7 mL |
| SC4-31 | 13R | 0.34N | 9.0 mL |
| SC4-34 | 13R | 0.28N | 9.4 mL |
| SC4-16 | 8R | 0.29N | 4.2 mL |
| SC4-25Z (316 s/s only) | 13R | 0.22N | 16.1 mL |
| SC4-21† | 13R | 0.93N | 7.1 mL |
| SC4-27*† | 13R | 0.34N | 10.4 mL |
| SC4-15 | 7R | 0.48N | 3.8 mL |
| SC4-28 | 13R | 0.28N | 11.0 mL |
| SC4-29 | 13R | 0.25N | 13.5 mL |
| SC4-14 | 6R | 0.40N | 2.1 mL |
| SC4-DIN-82 | 13R | 1.29N | 1.5 mL |
| SC4-DIN-83 | 7R | 1.29N | 1.5 mL |
| CHAMBER | TYPE | ||
| SC4-13R | Sample Chamber w/o temperature probe | ||
| SC4-13RPY | Sample Chamber w/RTD temperature probe & cable | ||
| SC4-8R | Sample Chamber w/o temperature probe | ||
| SC4-8RPY | Sample Chamber w/RTD temperature probe & cable | ||
| SC4-7R | Sample Chamber w/o temperature probe | ||
| SC4-7RPY | Sample Chamber w/RTD temperature probe & cable | ||
| SC4-6R | Sample Chamber w/o temperature probe | ||
| SC4-6RPY | Sample Chamber w/RTD temperature probe & cable | ||
| SC4-13RD-100‡ | Sample Chamber – Disposable, aluminum, 100 units | ||
Note: See page 39 for spindle/chamber ranges ‡ Requires the use of special water jacket SC4-45YD
* Also available as SC4-27D-100 = Disposable spindle, 100 units
† Solid shaft option available for spindles SC4-21 (Part No. SC4-21SD) and SC4-27 (Part No. SC4-27SD).
Reviews
There are no reviews yet.